islandprint82

How to Replace the Replacement Key Battery For the Saab 9-3 Saab owners must follow a set of specific steps to add a second ignition key. It requires dealer service with an electronic handheld computer called Tech-2. Then a new key as well as transponder have to be purchased and then programmed to the car. It is recommended to rotate your keys in order that one does not get worn out more quickly than the other. This will keep your keys in perfect condition. Replacement Case The new key fobs for keys are not like the old Saab keys. They have electronics which make it hard to copy. This has made stealing cars significantly more difficult than it was twenty years ago. It has also made it more costly to replace keys that were lost. Saab 9-3 owners must have two keys working. If one gets lost, it is expensive to purchase a new one for the car since it requires replacing the CIM module, and then reprogramming the locking cylinders. Dealers charge between $100 and $200 to do this. There are a few ways to avoid these costly. Some parts retailers will search for the code on an extra key (usually the same one that opens the doors and turns the ignition) and cut a brand new key blade from metal for a fraction of the dealer's cost. The key, however, must be identical to the original one in order to function within your car. Follow these steps to replace the case. You'll require an open-faced screwdriver and patience. With the screwdriver you can pull apart the plastic and remove the emergency key. After the case is open remove all electronics and put them in your new case. Be sure to put the correct badge and key back into the case, as well. Replacement Battery The Saab 9-3 replacement battery is a cheap part that can be quickly and easily replaced. This YouTube video by Cyclone Cyd demonstrates the procedure for replacing the remote fob battery in just four steps. This tutorial will work with any modern Saab key fob. However, the procedure might differ slightly. The button is typically located next to the Saab logo on the back of the fob. This button is usually located on the back of the fob, right next to the Saab Logo. Use a flathead screwdriver to insert the screwdriver into the tiny hole in this button. This should be enough to open the fob's case so that you can replace the battery. After the new battery CR1632 is installed, you can reassemble the remote key fob and program it to your car. The entire process should not take more than one hour. It's a simple process that does not require any special tools. If you lose your key, the process is slightly more complicated however, it can be completed. The dealer must read the car's VIN and then order a new key blade and TWICE module that has the exact unique code. After that, they will have to cut the replacement key and then program it using an innovative software tool called MDI. Replacement Key Fob The key fob is the part that locks and unlocks your car, it has a battery inside. The batteries last for a period of and will eventually die. This is a common problem that happens with all cars and the good thing is that you can replace the batteries in a majority of fobs, without replacing the whole case. You can buy replacement fobs from Amazon that come with all the electronic components already in place, so you'll just pop open the case and replace those batteries that are old. It is important to note that you'll have to remove the emergency key first. you can do this by inserting the screwdriver of a small flathead into the slot located in the middle of the case. The case should split when you work the screwdriver all around it. If you're planning to replace your keys, be sure to have a spare in your possession. This will save you a lot of money. If you have a spare, you can ask the dealer to cut the new key and program it to your car, which is much cheaper than replacing the entire key fob. If you do not have a spare key one, you can add a second key to your car, but it requires a lot of research and effort. The cost for adding a second key is several hundred dollars and it requires programming of the car's computer. Professionals can do this however, it's a costly option. Replacement Ignition As opposed to earlier Saab automobiles, the current SAAB 9-3 models are equipped with an extremely sophisticated alarm system that is built on a key code. If you lose only one key, it can be expensive to add another one since the car needs to have a special computer added and be programmed to accept a brand new key. Even dealers can charge hundreds of dollars to program a new key even if they're unable to complete the task. Dealers will charge you the highest price to replace your car computer (also called the CIM or SAAB twice) in the event that you lose your only working key. Instead we can reprogramme the EEPROM in your current car computer to allow it to be programmed for a replacement key, and save you over 50% of what you'll pay at a dealership. If saab 93 key fob G28CarKeys 've been a faithful owner of an 03-11 SAAB 9-3, then you likely are aware that the ignition key isn't all that robust. If your ignition key isn't working properly, you should consider replacing it. They can become very sticky and the buttons have been known to fall off. It's not as difficult as you think to replace the ignition key. With the right tools, it can be accomplished in a matter of minutes.